FDF24 ATEX

Productos
ATEX controllers
FDF24 ATEX

FDF24 ATEX

ATEX controllers
Control of solids

Intended use

Rotary blade level indicator for lateral mounting used in maximum, intermediate or minimum levels with protection tube, reinforced shaft and with a wide range of type varities depending on each application. The models are certificated for use in potentially explosive Dust and Gas atmospheres as well as in hybride mixtures (Dust + Gas) hazardous areas.

The rotary blade level indicator FDF observes the filling level as a limit switch. It can be used as indicator for dusty and powdery, granulated and grainy bulk goods and are appropriated due to the range of models and blades to control the level of bulk solids like dust, flour, grain, sand, plastic, etc. with a bulk density between 0.01 to 2 t/m³. Although the characteristics of the product, humidity, conductivity, grain size, etc. change, any adjustment is needed.

These devices are used to control the level in silos, containers, bunkers and they can be installed horizontally or vertically. They are versatile and universal usable because of their wide range of type varities. For vertical mountings there are rope shafts up to 10 m could be made depending on the product to control.

Function

The rotating measuring blade, projecting into the silo or container, is driven by a gearmotor. If the bulk material reaches the measuring blade, the rotation will be hindered and it will be stopped. The return torque turns the pivoted motor from its end position and actuates the signal switch. A second switch turns off the motor off.
If the filling level of the bulk material sinks, the blade becomes freely again and a spring will turn the motor back into its original end position. Thereby the motor will be turned on again and the signal switch will be switched back.

Mechanical connection

Rotary blade level indicator for lateral mounting into the silo.

The standard form is mounting the device with a flange, drilling holes on the silo to allow the mounting of the controller using screws, rods, fasteners or nuts.

After the mounting is done, the housing could be turned in order to face the cable gland correctly.

Dimensions

Approximate measures given in mm.

Technical data


Name	Rotary blade indicator
Type	FDF24
Certifications:	B1 Dust: ATEX II 1/2D Ex ta/tb IIIC T80° C Da/Db B2 Dust: ATEX II 1D Ex ta IIIC T₂₀₀ 70° C Da B3 Dust: ATEX II 1/3D Ex ta/tc IIIB T80° C Da/Dc A3-B1; A4-B1 Gas+Dust: ATEX II 1/2D Ex ta/tb IIIC T70° C Da/Db ATEX II 2G Ex db eb IIB T6 Gb A3C-B1; A4C-B1 Gas+Dust: ATEX II 1/2D Ex ta/tb IIIC T70° C Da/Db ATEX II 2G Ex db eb IIC T6 Gb
Switching voltage	Standard 230 V AC (50 – 60 Hz) (Under request 115 V AC, 48 V AC, 24 V AC, 24 V DC, 12 V DC due to a converter)
Power consumption	4 VA in AC; 4 W in DC
Density of the product:	0.01 t/m³ – 2 t/m³
Cable entry	2 of M20x1.5
Max. voltage of contact	4 V DC – 250 V AC
Contact function	1 NO + 1 NC
Capacity of the contact	1 mA / 4 V DC – 2 A / 250 V AC (for resistive loads) For inductive or capacitive loads reduce at 50%
Ambient temperature	-20° C – +70° C
Protection	IP66 according DIN EN60529
Weight	1.2 Kg – 5 Kg depending on the model
Other characteristics	Depending on requested options