Name | Rotary blade indicator |
---|---|
Type | F9-180 U.F. – ref: 9103-3... |
Measuring blade speed | 1 rpm |
Switching voltage | Standard 230 V AC (50 – 60 Hz) (Under request 115 V AC, 48 V AC, 24 V AC, 24 V DC due to a converter) |
Power consumption | 4 VA in AC; 4 W in DC |
Density of the product | 0,01 t/m3 – 2 t/m3 |
Maximum pressure | -0,5 bar – +1 bar (Under request up to +5 bar with sealing ring of Stainless Steel-PTFE-Viton) |
Cable entry | 2 of M20x1,5 |
Max. voltage of contact | 4 V DC – 250 V AC |
Contact function | 1 NO + 1 NC |
Capacity of the contact | 1 mA / 4 V DC – 2 A / 250 V AC (for resistive loads) For inductive or capacitive loads reduce at 50% |
Bulk goods temperature | -20° C – +80° C (Under request up to +150º C) |
Ambient temperature | -20° C – +70° C |
Protection | IP66 according to DIN EN60529 |
Weight | 1,2 Kg – 5 Kg depending on the model |
Materials: | |
Housing | Aluminium, RAL 7001 coated |
Thread connection | G 1 " 1/4 Aluminium |
Flange connection | Zincated Steel (Under request Stainless Steel) |
Measuring blade | S.S. 1.4301, shaft S.S 1.4305 (Under request special models of S.S. 1.4401) |
Sealing ring | NBR (Under request Stainless Steel-PTFE-Viton) |
Rod shaft | Stainless Steel |
- Productos
- Control of solids
- F9-180 U.F.
F9-180 U.F.
Intended use
Rotary blade level indicator for vertical mounting with anti-buckling protection.
The rotary blade level indicator F9 observes the filling level as a limit switch. It can be used as indicator for dusty and powdery, granulated and grainy bulk goods and are appropriated due to the range of models and blades to control the level of bulk solids like dust, flour, grain, sand, plastic, etc. with a bulk density between 0.01 to 2 t/m3. Although the characteristics of the product, humidity, conductivity, grain size, etc. change, any adjustment is needed
These devices are used to control the level in silos, containers, bunkers and they can be installed horizontally or vertically. For vertical mountings there are rope shafts up to 10 m could be made depending on the product to control.
Function
The rotating measuring blade, projecting into the silo or container, is driven by a gearmotor. If the bulk material reaches the measuring blade, the rotation will be hindered and it will be stopped. The return torque turns the pivoted motor from its end position and actuates the signal switch. A second switch turns off the motor off.
If the filling level of the bulk material sinks, the blade becomes freely again and a spring will turn the motor back into its original end position. Thereby the motor will be turned on again and the signal switch will be switched back.
Mechanical connection
There are models that can be mounted horizontally or vertically into the silo.
The standard form is mounting the device with a flange, drilling holes on the silo to allow the mounting of the controller using screws, rods, fasteners or nuts. If the flange was not requested, the thread is G 1 " 1/4 l and can be fixed using 1 or 2 nuts or introducing it into a threaded socket with a maximum of 25 mm length. If it is larger, the bulk goods have the possibility to deposit in the thread socket. This could provoke that the device becomes useless.
After the mounting is done, the housing could be turned in order to face the cable gland correctly.